1. Home
  2. Roof Flashing Guide: Types, Repair & Checks in WA
Seattle, WA

Roof Flashing in Seattle, WA

Roof flashing explained: step, kick-out and boot flashing per DOE guidance, how to check it, and flashing repair from Fenix Roof Service in WA.

Free · No obligation

Get a free estimate

About a minute. We call you back to set up a time.

What do you need?
Add email or details (optional)
  • 4.9 on Google
  • BBB A+
  • Insured & bonded

By sending, you agree that Fenix Roof Service may call or text you about this estimate. Urgent? Call (425) 344-8709.

Roof flashing means corrosion-resistant pieces lapped into the joints where a roof meets a wall or is pierced by a pipe or vent, so water runs onto the roofing, not into the house. Fenix Roof Service, a local, family-owned roofing company since 2016, repairs flashing, vents and boot pipes in Seattle, Kent, Tacoma, Renton, Auburn and Federal Way, WA. Leaks near those joints start with an on-site inspection.

Roof flashing basics: what it is and how it works

Roof flashing, as the U.S. Department of Energy describes it, works by overlap. The DOE Building America Solution Center guide on step and kick-out flashing says to "install corrosion-resistant flashing pieces that are overlapped in a shingle fashion." Each higher piece laps over the one below it, so water moving down the slope stays on the outer face of the layers.

Roof flashing goes wherever the roof surface is interrupted. The same DOE guide names two main places: roof-wall intersections, where a sloped roof runs into a wall, and roof penetrations such as pipes and vents. For penetrations, the guide calls for boot or collar flashings that are integrated with the roof membranes and shingles above and below the opening.

Roof flashing types named in the DOE guidance

Roof flashing types in the DOE Building America guidance come down to three pieces a homeowner should know by name: step flashing, kick-out flashing, and boot or collar flashing. The table below sums up where each one goes and what the guide says about it. The guide does not set every detail of every roof, so treat the table as a reference, not an installation manual.

Flashing typeWhere it goesWhat the DOE guidance says
Step flashingAlong a roof-wall intersection, worked in with each course of shinglesExtend it at least 4 inches up the wall from the roof deck and at least four inches out along the roof deck, overlapped in a shingle fashion
Kick-out flashingAt the lower end of a roof-wall intersectionInstall it at the end of the intersection to divert water away from the wall and into gutters
Boot or collar flashingAround roof penetrations such as pipes and ventsInstall it around all penetrations and integrate it with roof membranes and shingles above and below

Roof flashing against a wall: how step and kick-out pieces work together

Roof flashing against a wall is a two-part detail in the DOE guide: step flashing along the run of the joint, and a kick-out piece where that joint ends. The step pieces keep water on the roof side of the wall line; the kick-out turns the water at the bottom so it is sent toward the gutter instead of down the face of the wall.

  • A kick-out piece is placed where the roof-wall intersection ends, aimed toward the gutter.
  • Step pieces are laid with the shingle courses, each one overlapping the piece below in a shingle fashion.
  • Each step piece runs up the wall and out onto the deck by at least the 4 inches the DOE guide gives for each direction.
  • The wall's drainage layer above is lapped over the top of the step flashing, so wall water also lands on the outside of the pieces.
  • The gutter at the kick-out is checked so the diverted water has somewhere to go; Fenix also handles gutter installation and repair when that end of the system needs work.

Roof flashing metal, tape and sealant: what the cited guidance covers

Roof flashing metal is addressed in the DOE guide quoted on this page only in general terms: the pieces should be corrosion-resistant. The quoted sentences do not name one specific metal, gauge or finish, so the right material for a given roof is a question to put to the roofer who sees it.

Roof flashing checks: how often and what to look for

Roof flashing checks are tied to routine roof care in a USDA Forest Service publication, Overview of Roofing Materials for Forest Service Facilities, which states that "flashings should be checked twice a year when the roof is inspected and the gutters are cleaned." That sentence is guidance written for Forest Service facilities. It is a general reference, not a rule for homes in Washington State.

Roof flashing checks fit naturally with gutter cleaning, because the kick-out sends water into the gutter at the end of each roof-wall joint. For homes near trees, Fenix Roof Service recommends a yearly roof blow-off and gutter cleaning, and roof cleaning every three to five years depending on how much debris builds up.

  • Each roof-wall intersection has a kick-out piece at its lower end.
  • Pipes and vents through the roof have a boot or collar around them, tied in with the shingles above and below.
  • Ceilings and walls under these joints show no stains, drips or soft spots.
  • Siding just below a roof-wall joint shows no streaks or staining.
  • The gutter section that receives water from a kick-out is clear of needles and leaves.

Roof flashing repair or replacement: questions to ask in an estimate

Roof flashing repair estimates are easier to compare when each roofer answers the same questions. The DOE guide gives a useful yardstick: flashing pieces lapped in a shingle fashion, kick-outs at the ends of roof-wall joints, and boots or collars integrated above and below every penetration. Gaps against that yardstick are the details that can lead to rework.

  • Which flashing piece failed: step, kick-out, boot or collar?
  • Will the repair restore the overlap, or seal over the surface?
  • Is a kick-out present at the end of each roof-wall joint, and if not, is one included?
  • How will the wall's drainage layer be lapped over the new step flashing?
  • Will photos of the joint be shown before and after the work?
  • Does any nearby decking, vent or boot pipe also need attention?
  • Confirm permit needs with the City of Seattle, or the city where the house is, before work starts.

Roof flashing repair from Fenix Roof Service across the Seattle-Tacoma area

Roof flashing repair is part of the leak work Fenix Roof Service does, along with gutter leaks, vents, boot pipes, shingles and ridge caps. The crew gets up on the roof, takes photos and shows the homeowner what it finds, so the failed piece is visible before any decision is made.

Frequently asked questions

how roof flashing works

Roof flashing works as part of one drainage system that runs from the wall down to the roof. The DOE Building America guide says step flashing should be integrated with the drainage plane above, for example with house wrap overlapping it, so water running down the wall lands on the outside of the flashing and then on the shingles.

what does roof flashing look like

Roof flashing looks different depending on the piece. Step flashing sits mostly hidden under shingles and wall cladding, so from the ground only edges may show along a roof-wall joint. A kick-out appears as a small angled piece at the bottom of that joint, and boots or collars wrap around pipes and vents.

how to install roof flashing against a wall

Roof flashing against a wall on an existing house ties into the wall's cladding and drainage layer, not just the shingles, so replacing it can mean opening the wall covering at the joint. That makes it a job for a roofer, and permit needs should be confirmed with the City of Seattle or the home's city before work starts.

how to seal roof flashing

Roof flashing is kept watertight mainly by how the pieces overlap, according to the DOE guidance cited above. If a roofer seals a spot, ask to see photos of the joint and watch the ceiling and wall below it during the next rain, so you know whether the seal or the overlap was the real fix.

how to repair roof flashing

Roof flashing repair starts by finding which piece failed and why. Fenix Roof Service inspects the roof in person, photographs the joint and gives a free estimate with an on-site inspection; its repair work covers flashing as well as vents, boot pipes, shingles and worn decking.

From our own jobs

Found and fixed

What a repair looks like under the shingles. Photos from our crew, labeled with the city.

[FOTO REAL · PENDENTE FENIX: obra em Seattle]

Service area · Puget Sound

Where we work

From Arlington down to Gig Harbor and Port Orchard. Not on the list? Call (425) 344-8709 and ask.

  • 38cities
  • 4counties
  • 2016serving since

King County21

  • Seattle
  • Bellevue
  • Kirkland
  • Redmond
  • Shoreline
  • Bothell
  • Sammamish
  • Issaquah
  • Mercer Island
  • Renton
  • Tukwila
  • Burien
  • Kent
  • Federal Way
  • Auburn
  • Covington
  • Maple Valley
  • Duvall
  • Carnation
  • Snoqualmie
  • North Bend

Snohomish County9

  • Everett
  • Lynnwood
  • Edmonds
  • Marysville
  • Lake Stevens
  • Snohomish
  • Monroe
  • Granite Falls
  • Arlington

Pierce County6

  • Tacoma
  • Puyallup
  • Gig Harbor
  • Sumner
  • Bonney Lake
  • Graham

Kitsap County2

  • Bremerton
  • Port Orchard
PUGET SOUNDArlingtonLake StevensMarysvilleEverettGranite FallsMonroeLynnwoodEdmondsShorelineSnohomishBothellSeattleKirklandBellevueRedmondDuvallCarnationSammamishIssaquahMercer IslandSnoqualmieNorth BendRentonTukwilaBurienKentMaple ValleyCovingtonFederal WayAuburnBonney LakeSumnerPuyallupGrahamTacomaGig HarborBremertonPort OrchardN
Fenix service area: 38 cities in King, Snohomish, Pierce and Kitsap counties, Washington.

Free estimate

Let's take a look at your roof.

(425) 344-8709
(425) 344-8709Free estimate

Free · No obligation

Get a free estimate

About a minute. We call you back to set up a time.

What do you need?
Add email or details (optional)
  • 4.9 on Google
  • BBB A+
  • Insured & bonded

By sending, you agree that Fenix Roof Service may call or text you about this estimate. Urgent? Call (425) 344-8709.